Loading... Please wait...

Tensorgrip P307 Low VOC Canister Spray Adhesive 7 liters kit with hose and gun

  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5
P307-8# KIT

Product Description

P307 Low VOC Contact Adhesive 7 Liters container (1.85 gallons) Kit

Kit includes 12" hose, M120 Spray Gun and 9501 Spray Tip
Only ships to business addresses. No PO BOX or Residencial
Tensorgrip® P307
California Compliant  Spray Contact Adhesive
TENSORGRIP® P307 is a high solids, flammable solvent, web spray contact adhesive with good temperature resistance. TENSORGRIP® P307 is designed as a multi-purpose contact adhesive that effectively bonds a vast range of substrates while maintaining compliance with California VOC requirements.
Bonds vast range of materials, including plastics, HPL, wood, metal, foam, fabric, fiberglass and more 
Laminating (flexible to rigid material) 
Excellent bonding to porous substrates
General contact bonding 

Aggressive – Adheres to nearly any surface 
Fast dry with excellent initial bond 
Good heat resistance (up to 200°F) 
No urea formaldehyde added 
High-strength, long-term bond 
Web Spray  80% of final strength achieved immediately  
Full strength achieved in 24 hours  
Qualifies for LEED 3.2, 4.1, 4.4  
OTC compliant  
Low VOC California compliant (SCAQMD Rule 1168 Compliant ) 
TENSORGRIP® P307 is designed as a portable, self-contained spray system for field or shop applications. Adhesive should be applied to both surfaces to be bonded, allowed to dry (5-10 minutes or until dry to touch) then parts mated under pressure. Bonds should be made as soon as practical. If adhesive is left to dry for over 2 hours, parts should be recoated. Normal coverage required with lacing spray pattern is approximately 80%; however porous surfaces may need a second coat. Initial bond is strong enough to allow cutting or trimming immediately although ultimate strength is achieved in 1-3 days. Canister system will spray adequately above 60º F. Canister system should be kept in warm area. In the event that the canister gets abnormally chilled, freezes or gives poor or sputtering spray, it should be warmed up before continued usage. Warming canister by immersion in warm water is recommended. Notice!!! Avoid direct flame or exposure to excessive heat. Do not store at temperatures over 120º F. Not for use on flexible vinyl or polystyrene foam. Canister System Usage:  When hose is connected, keep canister valve open and hose pressurized at all times.  Do not disconnect the hose until ready to connect to new canister.  Release pressure in hose before disconnecting from canister.  If gun and hose must be stored unattached to pressurized canister, they may be cleaned for future use by attaching to canister of 609 Citrus cleaner and flushing until clear.
VOC Content:   79 g/L  Solids:  32-38% Appearance:  Clear Liquid Solvent System:  Methyl Acetate/N-Hexane Shelf Life:  15 Months
Coverage: 87 ft2/lb
Canister Adhesives

Canister adhesives are designed as portable, self-contained spray systems for field or shop applications.  No outside air source is required.  The only equipment needed is a hose and spray gun.  However, compressed air may be used to improve sprayability and increase dry times.  Typically these are not big issues as canister adhesives are quite fast dry with extended open times allowing for sufficient workability.

  • These adhesives are available in 650 ml. aerosol cans – 7Liter Mini – 22Liter Large – 108Liter Intermediate – 216Liter Jumbo size canisters.
  • Transfer efficiency of canister adhesives is <90%.  
  • Transfer efficient.

Find Similar Products by Category

Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...